Scanmix CONFLOW SP 50

arrow_hist Special mixtures arrow_hist Floor mixes arrow_hist Scanmix CONFLOW SP 50
Scanmix CONFLOW SP 50

Floor screed for solid, non-deformable substrates made of concrete or mortar, used for laying and repairing floors inside and outside buildings; for the manufacture of floors with a slope; for the preparation of bases for self-leveling mixtures: CONFLOW 200, CONFLOW 300, CONFLOW GP, as well as for laying ceramic tiles.

Material consumption calculator

Enter the surface area, m²

You will need approximately 0kg

PROPERTIES:

  • 10-80 mm layer thickness
  • Waterproof
  • Instant verification
  • Frost resistant
  • Abrasion resistant
  • Environmentally sound

PREPARATION OF THE BASE:

The base must be seasoned (at least 28 days), non-water-absorbing, rigid, durable (strength not less than megapascals in compression – 20 at break -1, 5) and resistant to deformation from external loads. The covering of ceramic and stone tiles, as well as wood, polymer, asphalt is removed. The substrate is cleaned of sagging, areas of weak strength and substances that reduce adhesion (fats, oils, paints, etc.). Remove the weak surface layer with a sander, sandblaster or steel brush. Existing cracks must be widened and mechanically deepened to a depth of 1/2 of the top layer thickness and up to 5 mm wide, primed and closed with Scanmix SP. The resulting dust is removed with a vacuum cleaner. A cleaned surface with high water absorption is impregnated with Scanmix primer and dried until the gloss disappears on the surface, but not less than 4 hours. Insufficient quality of preparatory work can lead to delamination or cracking of the laid layer. When preparing the foundation and performing work, be guided by the requirements Building regulations 3.04.01-87 and State Building Norms of Ukraine V.2.6 -22 -2001.

PERFORMANCE OF WORK:

Pour the dry mixture into a container with clean water at room temperature in the proportion: 0,12 liters per 1 kg of the mixture (3,0 liters per 25 kg bag). Stir with a drill with a nozzle or by hand until smooth without lumps and clots, stand for 5 minutes and mix again. If the mixture thickens within 1 hour from the moment of mixing, its mobility can be restored by repeated mixing without adding water. Use a clean tool for cooking. The solution is emptied directly from the container. After applying the solution, it must be distributed using a rail – a rule or a shovel, a special rake, after which it is compacted and smoothed with a vibrating screed, a power tool (with a smoothing disc, a machine with a smoothing propeller) or manually – with shovels, trowels, tapping with stroking or in another way, until complete compaction (the surface begins to shine). The final leveling and smoothing can also be done with a metal float. On an area of ​​more than 20 m², it is necessary to perform shrinkage joints (with silicone sealant) to prevent mechanical deformation and it is necessary to ensure the isolation of the nested screed from vertical surfaces by installing foam or foam inserts with a thickness of 3 … 5 mm along the perimeter of walls, columns, foundations, etc. In screeds with a thickness of more than 40 mm, in order to save mortar and protect against the occurrence of shrinkage cracks, it is recommended to add a large (no more than half the layer thickness) aggregate (expanded clay, crushed stone (granite or solid brick)), in an amount not exceeding the initial volume mortar mixture. At the same time, the strength of the screed is reduced accordingly. During the hardening of the mortar in the first two days, it must be protected from direct sunlight and drafts, and adequate ventilation must be provided. Work must be performed at a surface temperature of +5 ° C to +30 ° C. The most effective result is achieved at a temperature of +20 ° C and a relative humidity of 60%. Protect the screed from drying out by eliminating drafts or covering with a waterproof film. After hardening, until the desired strength is reached, it should be kept moist. In other conditions, the operating parameters of the mixture may change. The manufacturer is not responsible for the improper use of the material, as well as its use for other purposes and conditions not provided for in the technical description.After finishing work, the tool must be washed immediately. Technological movements on the surface can be carried out 24 hours after the application of the solution. The floor is ready for further use in 3 days after application.

SAFETY PRACTICES:

Do not pour mortar and water into sewer pipes after work. It is advisable to wear rubber gloves. Avoid contact of the solution with the skin or eyes. In case of contact with the skin or eyes, rinse thoroughly with water, since the mixture contains cement, which, when mixed with water, forms an alkaline medium.

SHELF LIFE:

In dry space and on pallets, in factory packaging: 12 months from the date of issue indicated on the package.

PACKAGE:

The dry mixture is packed in paper bags of 25 kg.

TECHNICAL CHARACTERISTICS:

COMPOSITION: Cement mixture with mineral fillers and organic additives.
Maximal grain 0,6
Amount of water to mix solution 0,16-0,20 l/kg mixture
Usage time 1 hour
Air temperature and bases when used From +5°С to +30°С
Compressive strength 15 megapasal
Ready for use (depending on layer thickness) After 48 hours
Consumption (depending on the thickness of the layer applied)
Near 1,7 kg/m2 per 1 mm
Recommended thickness of the layer From 10 mm to 40 mm
Tensile strength at bending min 3,5 megapasal
Operating temperature From -30°C to +70°C
Frost resistance, cycles, not less 50