Scanmix MULTISUPER Grey 119

arrow_hist Glue
Scanmix MULTISUPER Grey 119

Glue for tile, grey, high elastic, is intended for coating surfaces with increased ...

Read More
Scanmix TEPLO 118

A mixture for facing stoves and fireplaces, as well as for work on durable non-deforming ...

Read More
Scanmix KLADKA 121

The cellular heat-retaining glue is used for erecting external and internal walls with ...

Read More
Scanmix TERM FIX 210

Glue for mineral cotton wool and for foamed polystyrene plates, which is used in the ...

Read More
Scanmix UNIVERSAL 220

Adhesive and reinforcing mixture for heat-insulating plates, is used in the system of ...

Read More
Scanmix TERM ARMIX 240

Adhesive and reinforcing mixture for mineralized and foamed polystyrene plates, is used ...

Read More

PROPERTIES:

  • Fibre-reinforced mixture
  • Elevated adhesion
  • Resistant to temperature and vibration
  • Nonshrinking
  • Ideal for old ceramic surfaces
  • Rapid pace of work
  • User-friendly
  • Highly plastic
  • Frost resistant
  • Waterproof
  • Environmentally friendly

PREPARATION OF THE BASE:

The base shall be dry, strong, dust-free, dirt-free, lime-free, grease stains or paint. The loose, defective layer shall be removed. All bases are processed 1-2 times with primer SCANMIX. Before laying the tiles on the old ceramic surface, the latter must be degreased with caustic soda (1 kg per 10 litres of water) and washed with clean water.

PERFORMANCE OF WORK:

The tile is not wetted. The adhesive solution is mixed manually or mechanically with clean water until a uniform consistency is obtained. After 5 minutes, the finished solution should be stirred again. The solution is applied in a thin layer to the prepared surface with the aid of a suitable toothed spatula (the size of the teeth can vary between 6 and 10 mm). The solution is applied so that the tiles can be glued in 30 minutes. Due to the special properties of the solution the laid tiles are fixed on the surface, and within 15 minutes it is possible to adjust its position. After 48 hours the surface can be used and the seams can be fudged.

When laying the tiles on the heated surface, it is necessary to warm the floor by turning on the heating, and 1-3 days before work is done to turn it off. The heating can be used 2 days after the fumigation of the seams.

Under adverse weather conditions (high temperature, dry wind, direct sunlight), the time taken to apply a surface solution can be significantly reduced.

The instrument is washed with clean water immediately after use and contaminated tiles before/after laying.

The manufacturer shall not be liable for improper use of the material or its use for purposes and conditions not provided for in the instruction.

SAFETY PRACTICES:

The solution and water should not be poured out after working in sewer pipes. It is desirable to work in rubber gloves. Contact with the skin or eyes shall be avoided. If the solution enters the skin or eyes, it is necessary to wash it thoroughly with water, since the mixture contains cement which, when mixed with water, forms an alkaline medium.

SHELF LIFE:

In dry space and on pallets, in factory packaging: 12 months from the date of issue indicated on the package.

PACKAGE:

The dry mixture is packed in paper bags of 5 kg and 25 kg.

TECHNICAL CHARACTERISTICS:

COMPOSITION: Cement sand modified with polymer additives
Color white, gray
Placeholder size not more than 0,3 mm
Amount of water to mix solution 0,16-0,18 l/kg mixture
Final solution time 240 min
Open time 25-30 min
Adjustment time 15-25 min
Base temperature of mixture application from +5°С to +35°С
Operating temperature from -50°С to +120°С
Strength of adhesion to concrete base 1,7 megapascal
Flexural strength not less than 2,5 megapascal
Layer thickness not more than 15 mm
Technological transfer time 48 hours
Joining seams 24 hours
Frost resistance at least 50 cycles
Consumption (depending on the thickness of the layer applied)  2 to 7 kg/m2