Scanmix INTERIOR DELUXE

Scanmix INTERIOR DELUXE

Water-based dispersion paint for interior use. Designed for painting walls and ceilings ...

Read More
Scanmix MATTLATEX DELUXE

Interior latex paint. Designed for painting walls and ceilings made of cement, ...

Read More
Scanmix SILICONE FACADE B3

Silicone facade paint for toning on toning equipment in saturated bright shades according ...

Read More
Scanmix Acril Structur-farbe

Structural acrylic paint is intended for creating decorative textured coatings indoors ...

Read More
Scanmix SILICONE Structur-Farbe

Structural facade paint with the addition of silicone. Designed to create decorative ...

Read More
Scanmix KLADKA 121

The cellular heat-retaining glue is used for erecting external and internal walls with ...

Read More

PROPERTIES:

  • Thickness of layer 2-8 mm
  • User-friendly
  • Prevents the formation of “cold bridges”
  • Plastic
  • Frost resistant
  • Waterproof
  • Environmentally friendly

PREPARATION OF THE BASE:

The preparation of the framework shall be in accordance with State Building Norms of Ukraine V.2.6-22-2001. The base shall be clean, strong, dry. The roughness and imperfect parts of the base must be cleaned and then leveled with a dissolved mixture 24 hours before the start of work. To improve the adhesion, the surface needs to be treated with SCANMIX primer. The gluing work shall not commence until two hours after the primer has been applied.

PERFORMANCE OF WORK:

Fill the dry mixture with clean water (water temperature from +15°C to +20°C) at a rate of 0.16-0.20 l/kg adhesive and mix until a homogeneous mass without lumps is obtained by means of a low-rotating drill or mixer. Then the dissolved mixture will last 3-5 minutes, then mix again. The solution is suitable for use for 4 hours. The prepared mixture is uniformly applied to the contact surface with the aid of a cologne or a steel spatula and evenly distributed by a toothed spatula. The blocks are applied, slightly pressed. The glue is performed within 20 minutes from the time the solution layer is applied to the base. Once the blocks have been laid, they can be adjusted for 10 minutes. The solidification time of the mixture depends on the type of base, temperature and humidity of the air and is about 24 hours.

The work must be performed at a base temperature ranging from +5°C to +30°C. All the above recommendations are most effective at a temperature of +20°C and relative humidity of 60%. Under other conditions, technological parameters may change.

The manufacturer shall not be liable for improper use of the material or its use for purposes and conditions not provided for in the instruction.

SAFETY PRACTICES:

The solution and water should not be poured out after working in sewer pipes. It is desirable to work in rubber gloves. Contact with the skin or eyes shall be avoided. If the solution enters the skin or eyes, it is necessary to wash it thoroughly with water, since the mixture contains cement which, when mixed with water, forms an alkaline medium.

SHELF LIFE:

In dry space and on pallets, in factory packaging: 12 months from the date of issue indicated on the package.

PACKAGE:

The dry mixture is packed in paper bags of 25 kg.

TECHNICAL CHARACTERISTICS:

COMPOSITION: Mixture of cement with mineral fillers and special additives
Color gray
Maximal grain 0,3 mm
Amount of water to mix solution 0,16-0,2 l/kg mixture
Layer thickness from 2 mm
Life of dissolved mixture up to 4 hours
Compressive strength not less than 10 megapascals
Strength of adhesion to base (dry air) not less than 0,5 megapascals
Frost resistance 50-70 cycles
Core temperature from +5°С to +30°С
Operating temperature

Thermal conductivity

from -50°С to +90°С
not greater than 0,17 Thermal conductivity
Consumption*  2 to 3 kg/m2/mm

* Depends on spatula teeth size and base roughness (1 bag of mixture – average of 55 foam concrete blocks of 200x300x600 mm)